Products
Jan 01, 2020 · Streptomycin stock solution (100 mg/mL): Dissolve 1 g streptomycin sulfate (e.g., Cat. No. 0382, Amresco, Ohio, USA) into 10 mL distilled water at a concentration of 100 mg/mL and filter it with 0.22 μm PES syringe filters. Aliquot into 1 mL for each tube and store at − 20 °C. •
Direct healthcare professional communication (DHPC): Tepadina (thiotepa) 100 mg: possible risk of defective vials in batches n°1709192/1, n°1709192/2 and n°1709192/3 presenting a crimp seal not properly fixed on the vial. Active substance: thiotepa, DHPC type: Quality defect, Last updated: 02/06/2020. List item.
1) Spun - Melt Blow Dept Filter - Economic and effective. 2) PP Pleated Filter cartridge - Economic and effective. 3) Hydrophilic Nylon/PES Filters for finer filtration, long service life, low extractable. 4) SS Sintered / Pleated / Titanium filters for high temperature water filtration. 5) PTFE Filter for Venting Purpose.
Push the syringe barrel to wet the filter unit and deliver the wetting fluid into a container. Disconnect the syringe from the Integrity Test Kit for small volume devices assembly. If there is any liquid left in the syringe, push the syringe plunger to empty. Withdraw the syringe plunger to the 60 mL line to fill the syringe with air.
• Thermo Scientific™ Nalgene™ 25 mm Syringe Filters, PES, 0.2 µm (P/N 7252520) • AirTite™ All-Plastic Norm-Ject™ Syringes, 10 mL, Sterile (Fisher Scientific P/N 14-817-31) • Thermo Scientific™ Nalgene™ 1000 mL, 0.2 μm Nylon Filter Units (P/N 09-740-46) Software Data acquisition • Thermo Scientific™ Chromeleon
Endotoxin and Pyrogen Removal. Pyrogens are substances that induce a fever when injected into humans and animals and endotoxins are the single most important class of pyrogens. Depending on the states of aggregation, endotoxins can have individual molecular weights of 10-120kDa, or molecular weights as large as 1,000kDa.
Dec 29, 2019 · Step6: Fluorescence Cuvettes. Fluorescence cuvettes for fluorometers have 3 or 4 walls transparent while spectrophotometer cuvettes have 2 walls clear. The QG10204-4 quartz cell is the most basic cuvette for UV VIS measurements. This cuvette has all four windows polished and comes in the UV grade quartz.
Filter all water samples through a 0.2 μm Nalgene PES syringe filter. A 0.45 µm pore size filter of the same material should also be effective. Discard the first 300 μL of filtrate and filter the remainder directly into a clean plastic autosampler vial. Prepare aqueous soil extracts by adding 30 mL of 30 mM MSA to 3.0 g of soil. Extract in an
May 29, 2015 · The PES filter was the best-performing filter in the moderate group. Although total lead loss averaged only 6.4 %, which actually fell in the good-filter group, significant lead losses to the PES filter were noted in the first 15 mL volume filtered, which put it in the moderate category.
Dec 22, 2014 · Incorrect filter use may lead to: • Increased time to filter a sample • Need for multiple filters to obtain the required volume for the analysis instead of one • Increased pressure to push liquid through the syringe filter • Bursting the membrane and/or filter housing • Observation of leachable in the results due to solvent
Polypropylene, nylon, and PTFE membranes are ideal for sample preparation and small volume chemical filtration.Syringe filters are attached to the end of a syringe to remove particles from a sample prior to analysis. Filtering liquids, the single-use devices force liquids through the filter either when fluids are initially drawn or delivered. Circular shaped in diameters that fit common
*If you require a pore size or diameter not listed in the table please contact us to see if we can provide you with a syringe filter to meet your specifications. See full list on ossila.com Membrane filtration is a method of removing particulates from solution without the need for any heating. This filtration method is typically used in other processes, such as sublimation and distillation. It works simply by restricting the movement of particles above a specific size through a porous material. Typically membrane filtration is separated into several categories dependent upon particle size. These categories are: particle filtration, microfiltration, ultrafiltration, nanofiltraion, and reverse osmosis. These different categories cover particle sizes, ranging from centimetres down to angstroms. Below is an image highlighting the range covered by microfiltration membranes highlighting the types of materials that can be filtered out. Membrane filtration is used in a variety of scientific fields including biotechnology, pharmaceuticals, medicine, chemistry, and semiconductor manufacturing. Each field has very different requirements for the filters and the choice of filter ty See full list on ossila.com At Ossila, we offer five different membrane materials for our syringe filters: 1. Hydrophobic PTFE (Polytetrafluoroethylene) 2. Hydrophilic PTFE 3. Hydrophobic PVDF (Polyvinylidene fluoride) 4. PES (Polyethersulfone) 5. Nylon PTFE can be used with almost any solvent due to its low reactivity and low extractables. Additionally, PTFE has extremely high thermal stability, allowing for a wider range of processing temperatures compared to standard membrane materials. However, PTFE is naturally hydrophobic, which can make the filtering of aqueous solutions difficult. To counter this, we offer the option of hydrophilic PTFE - in which the membrane surface has been treated to improve the wetting on aqueous solutions. PVDF like PTFE is naturally hydrophobic and like PTFE offers high chemical resistance against a wide range of different chemicals. PVDF also has the advantage of low protein binding in comparison to materials such as PTFE. Due to its naturally hydrophilic nature, PES is compati... See full list on ossila.com
Dual layer PROPOR HC PES 0.2 µm PVDF 0.2 µm Protein binding on membrane materials 140 120 100 80 60 40 20 0 Protein Adsorption (mg / cm 2) Nylon Polypropylene Polysulphone PVDF Pdh PES Membrane Material HSA g-globulin Insulin Micron Rating 0.2 Filter Cartridges / MURUS / DEMICAP / Syringe Filters Min. Bubble Point (barg) 3.4 (psig) 49.0
A variety of membranes are available to meet your needs: Polyethersulfone (PES) – low protein binding and faster flow rates; surfactant-free cellulose acetate (SFCA) – lowest protein binding; polytetrafluorethylene (PTFE) – chemical resistance; regenerated cellulose (RC) – best choice for DMSO compatibility; Nylon (NY) – hydrophilic, surfactant-free, and lowest extractable. 100%