Products
Headspace vials, flat top, rounded bottom, pkg of 100 volume 10 mL, clear glass vial, crimp top (0.125 in. thick) for thin septa, O.D. × H × I.D. 23 mm × 46 mm ...
Mar 28, 2017 · Detectable ethylene in headspace vials decreased in a linear fashion over time and showed a strong temperature dependence (Figure 6). After 24 h of storage at −20°C, the 5 p.p.m. reference samples had lost an average of 50% while samples stored at 4°C and 25°C had lost 18% and 23%, respectively.
Ambient air samples were collected into 20 mL crimp vials (i.e., by opening the vial to air and shaking for ~60 sec) and then sealed with aluminum caps and PTFE-silicone septa (Aijiren, Santa Clara, CA, USA). Vials were transported to the laboratory in 1 L clean glass jars to prevent possible losses of analytes during the transportation.
The spectrum for the unknown, the reference spectrum you select from the list of hits, and, if available, the chemical structure of the reference compound is displayed. 4 To view other spectral data: - Click another compound in the hit list to display a different reference spectrum.
A J&W capillary column HP-5 MS UI of 30 m × 0.250 mm with 0.25 μm film (Aijiren Technologies Inc.) was used for the separation. The ICS samples in a 20 mL headspace vial were heated at an equilibrium temperature of 130 °C for 40 min, and the gas phase were injected into the GC-MS for analysis. The injection time was 1.0 min.
Vials, 2 mL, open-top screw cap, R.A.M. ™ (9 mm) convenience kit with closures with septa, unassembled, pkg of 100 11 Product Results
Crimp Top Vials, Caps and Kits The wide opening crimp cap provides a larger target area for improved autosampler needle accuracy. Select from four cap colors and a variety of septa. Whatever your crimp top vial needs, Aijiren has what you are looking for. • 2 mL, 12 x 32 mm • Tightly controlled crown for improved crimping
Nov 30, 2020 · Since 1875, Shimadzu is pursuing leading-edge science and technologies in analytical and measuring instruments including chromatographs and mass spectrometers, medical devices, aeronautics, and industrial equipment.
Feb 23, 2020 · Prepare serial dilutions of stock level A into separate headspace vials. Use a cemented needle syringe from SGE Corp. (not a plastic-tip pipettor) to add the specified levels (Table 1) of stock solution A to 20 mL crimp-top headspace vials by injecting through the septum. Use the high precision 1-µL analytical syringe to accurately pipette
May 21, 1999 · From the data in Table 1 we see that the volume of headspace gas during an acceptable sampling time is surprisingly small and less than 1% of the available total headspace gas in a headspace vial of typically ca. 20 ml volume. It is obvious that the admissible sample volume increases with the cross section of the capillary column.
An adequate amount of irradiated liquid polymeric material from p(N iPMAm) was put in a headspace vial of 20 cm 3, closed with aluminum crimp cap with a polytetrafluoroethylene/silicone septum (PTFE/Si, 20 mm, Aijiren Technologies, Santa Clara, CA, USA) and placed in an HS autosampler (Aijiren Headspace Sampler) of a gas chromatograph
A headspace sampler (HS) is an instrument that can perform thermal extraction in solid or liquid matrices. The solid/liquid samples are placed in HS crimp-top glass vials and heated at a set temperature for a fixed amount of time (as seen in Figure 1). The instrument is built so that the vial can be equilibrated and shaken in the oven precisely.
The ChemSensor and Headspace ChemSensor Sy stem were equipped with ChemSensor Software (Aijiren Technologies). This software creates a sin-gle fi ngerprint mass spectrum regardless of retention time. Headspace sampling. 1 mL aliquots of the fl avors were placed into 10 mL vials, which were sealed with crimp
Cap headspace vial with septum stopper/aluminum seal and crimp the seal with the crimper. Repeat above steps until all calibrators, controls and samples have been aliquoted. The following is the preferred position allocation of run sequence for case samples. Ethanol 50 mg/dl – Level 1 calibrator Ethanol 100 mg/dl – Level 2 calibrator
Jul 18, 2020 · Place the open end of the sample coring tool over a clean headspace gas vial and use the plunger to push the sediment into the vial. 5. Immediately place a gasket with a crimp top over the vial and crimp shut. 6. After sealing the vial, immediately write down the sampling interval, location, and any other information for the sample that was